Wireless WIFI Bridge Network Internet Point to Point WIFI Extender 300Mbs 3KM

Wireless Outdoor Digital dialing CPE/AP 5.8G / 3KM / 300Mbs / Client Bridge/CPE, Directional Antenna, Remote, Point to Point, Weatherproof IP65 Important Tips: CPE 300Mbps high-speed, 5.8GHz frequency, 3km stable transmission, IP65 outdoor waterproof level. 1. The distance “3KM” means 2pcs CPE based on point to point bridge mode，3KM means barrier-free 3KM range, in actual use, 2 CPE installation should be lower than 3KM. 2. To achieve the CPE function, one needs to act as a receiver and the other one to as a transmitter, so 2pcs wireless bridge will achieve a better signal effect. You must purchase at least 2 to use. Specification： Chipset：AR9342 Transmitting power：100mW DDR: 64Mbyte FLASH: 8Mbyte PoE Power: 12V—24V Antenna: 14dBi directional Physical Ports: 1 10/100Mbps Ports Key: 1 digital display key Dial code: left and right dial switch Power LED On ：The power is on/system starts Off： The power is off/system closes Four signal strength indication LED all lighting up means the signal strength is at the highest level; Four signal strength indication LED all blinking means the signal strength is at the weakest level Operation Temperature: -20~+70 Operation Humidity: 10%~95% RH Package Inlcude: 1 x CPE 1 x POE Adpter 2 x Tips 1 x User Manual Note : Products with electrical plugs are designed for use in the US. Outlets and voltage differ internationally and this product may require an adapter or converter for use in your destination. Please check compatibility before purchasing. Applications Applications Case 1: My son and I were trying to figure out a solution for his garage. We have a lot of high-tech gear out there, and it relies on the internet. We have tried standard Wi-Fi repeaters and mesh systems. They just don’t have the range we need. We even tried a string of Wi-Fi range extenders connected to each other, with a cable between. Both just didn’t work. Not reliably, not at all. The distance was just too great. It’s nearly a mile from the house and that is just too far. CPE71C wireless bridge wiring it up was pretty straightforward. We connected the one unit on the gateway in the house, we mounted it on the porch. We then set up the garage unit to the eve, facing the housing unit. We were lucky with a nice line of sight where we wanted to set up. In the garage, we connected it to the WAN port on a Wi-Fi router and we are in business. The speed is phenomenal. It is as fast as I. The house, not really any more noticeable lag either. Our phones now connect to Wi-Fi. The diagnostic systems are all connected to Wi-Fi. The smart TV is live. And the laptops are all running. We can stream, and even play some games. I can even stream movies from our DLNA server up at the house. This has solved a major headache for us. I assure you, our cell carrier is sad about it now that we aren’t going over our data anymore. Applications Case 2: We have a second building that is about 150′ from our main building and needed stable internet for both employees and security systems. I tried reaching it with our mesh routers, but even placing one on an outside wall wouldn’t supply a stable signal. We could have installed a second modem/router but that would add hundreds to our initial install and monthly costs. Installing this bridge has offered a stable signal and wiring it into a mesh system, it has allowed us to expand our net throughout the second building. Access Wireless Bridge Via Computer A. Modify your computer’s IP address. Make your computer’s IP and the bridge’s IP address be on the same network segment(LAN) so that you can access them. Step 1: Find and open “Open Network and Sharing Center” on your computer. Tips： click the network icon in the lower right corner of the computer. Step 2：Find and open the “Change adapter settings”, select “Local Area Connection” to right-click to open the network properties. Refer to the picture above to open. Step 3: Find and double-click open the “Internet Protocol Version 4(TCP/IPv4)”, choose the ” Use the following IP address” and enter IP address, subnet mask, Default gateway, Preferred DDS server. B.Connect the CPE to the computer via Ethernet cable and PoE adapter. Before accessing CPE, please make sure that you have set the computer IP address and the network segment of the wireless bridge IP to be the same. C. To configure the wireless bridge, open a web browser. In the address bar of the web browser, enter the CPE IP address (such as 192.168.211.40). A login screen will appear, the password of the wireless bridge is “admin”, just entry password login. Point to Point Extend Network WiFi Range Extend the network in the house to your barn, garage, church, warehouse, even neighbor’s house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money. Point to Point Extend Video Surveillance Range Help you expand the surveillance range, install surveillance cameras outside the yard without the need to lay network cables and cables. UeeVii Outdoor Wireless Bridge Thank you for choosing UeeVii CPE71C Wireless Bridge. Please read this user manual carefully before use, and keep it for future reference. If you need any assistance please feel free to contact our customer support team by email . UeeVii Outdoor Wireless Bridge Model: CPE71C Package List: 2 x CPE71C 2 x PoE Adapter 2 x Cable Ties 1 x User Manual Note: The CPE using “Ethernet cable” and “PoE adapter” for the power cable and adapter, so the DC power supply is not included. Follow standards：IEEE802.11a，IEEE 802.11n PoE Power：24V Antenna：14dbi, MIMO 2×2 (2Tx,2 Rx) Wired interface: 1 * 10/100Mbps LAN port Network Speed: 100Mbps Applicable distance：>3KM