Пара подшипников передних или задних колес для Honda Element 03-2011 Honda CR-V LH или RH

What’s in the box? 2 Pcs Wheel Bearing and Hub Assembly Specifications: Location: Front Wheel Material: Bearing Steel ABS Sensor Included: No Outside Diameter: 84 MM Design:Double Row Angular Contact Inner Race Bore: 45 MM Compatible Vehicles: Pair For Honda Element 03-2011 Honda CR-V Front or Rear Wheel Bearing LH or RH What’s in the box? 2 Pcs Wheel Bearing and Hub Assembly Specifications: Location: Front Wheel Material: Bearing Steel ABS Sensor Included: No Outside Diameter: 84 MM Design:Double Row Angular Contact Inner Race Bore: 45 MM Compatible Vehicles: Fits Acura Cl 2001-2003 Fits Acura Mdx 2001-2002 Fits Acura Rsx 2002-2006 Fits Acura Tl 1999-2003 Fits Honda Accord 1998-2002 Fits Honda Civic 2004-2005 Fits Honda Cr-V 1997-2001 Fits Honda Cr-V 2002-2004 Fits Honda Element 2003-2011 Fits Honda Pilot 2003-2007 Fits Honda Pilot 2008 Fits Honda Prelude 1997-2001 Fits Honda S2000 2000-2009 The wheel hub bearing needs to be replaced in the following situations（notes） A humming, rumbling or growling noise that increases with acceleration or as the vehicle turns Vibration, felt in the steering wheel, which changes with vehicle speed or as the vehicle turns Looseness or excessive play* in the steering wheel (especially while driving over rough road surfaces) A loud, constant grinding noise when driving the vehicle (heard in the most severe cases of a wheel bearing failure) Puling to one side when braking Roughness or vibration when rotating the wheel with the vehicle off the ground Excessive brake pedal “play” (can also indicate excessively loose wheel bearings) ABS light illumination or system issues (may be related to failure of the ABS sensor in the hub assembly or the internal sensor in the wheel bearing) Purpose and Commitment : We insist on innovation and development. Our everlasting purpose is high quality , Integrity-based and Full service. Removing and Installing a Hub Unit Bearing: 1. Wheel End Disassembly Remove all old lubricant from the rotor/ hub assembly and spindle. Clean the rotor/hub assembly and spindle with kerosene or mineral spirits. Inspect the spindle for wear. Use a fine file, wire brush, emery cloth or honing stone to remove any debris, nicks or burrs. Follow the vehicle manufacturer’s recommendation for permissible spindle wear. Apply a light grease coating on the cone seats to ease installation and prevent fretting. 2. Clean and Inspect Hubs and Spindles Use a cup driver or mild steel bar to drive the new inner cup and outer cup into the hub/rotor assembly until solidly seated against the hub shoulders. Be careful not to damage the cup surfaces. Never use a bearing cone assembly to drive a cup. 3. Install cups Use a cup driver or mild steel bar to drive the new inner cup and outer cup into the hub/rotor assembly until solidly seated against the hub shoulders. Be careful not to damage the cup surfaces. Never use a bearing cone assembly to drive a cup. 4. Lubricate Use a mechanical grease packer to pack the inner bearing cone assembly with grease. Place the bearing cone assembly, small end down, into the grease packer funnel. Plug the bore of the large end of the bearing cone assembly with the conical retainer. Firmly press down on the conical retainer. This forces the grease between the rollers, cage and cone. Smear excess grease on the outside of the bearing cone assembly. Pack grease between the inner and outer cups in the hub cavity. Also, liberally coat the hub cap inner wall. This layer combats moisture and retains the grease in the inner and outer bearing cone assemblies. 5. Install Grease Seal Replace the grease seal when it leaks or when bearings are being repacked or replaced. Install the inner bearing cone assembly in the hub, then install the new seal. Make sure the seal lips are pointed in the right direction following the vehicle manufacturer’s specification. Use the proper seal installation tool. 6. Install Rotor/Hub Assembly Be careful not to damage the seal against the spindle when sliding the rotor/hub assembly back over the spindle. After following Step 4, pack the outer bearing cone assembly with grease. Install the outer bearing cone assembly, washer and adjusting nut on the spindle. 7. Bearing Adjustment Use a torque wrench to tighten the adjusting nut to 50 ft. lbs. while turning the rotor. Back off the adjusting nut 1 full turn. Re-torque the nut to 10 ft. lbs. while turning the rotor. Next, back off the adjusting nut ¼ turn. Lock the nut with a new cotter pin. 8. Check Bearing Adjustment Use a dial indicator to measure endplay. Mount the indicator base as close to the center of the hub/rotor as possible. With the indicator tip against the end of the spindle, set the indicator at zero. Grasp the rotor at three o’clock and nine o’clock. Push the rotor in while oscillating and read the dial indicator. Dial IndicatorPull the rotor out while oscillating and read the dial indicator again. The bearing end-play is equal to the total indicator movement, which should be between 0.001” and 0.005.” If not, repeat steps 7 and 8. Reinstall all components as the vehicle manufacturer recommends. Warning failure to observe the following warnings could create a risk of death or serious injury!!! Item Specifics Placement on Vehicle Left Warranty 1 Year Manufacturer Part Number SUA802862cars Interchange Part Number 510050,42200S3VA01, 44300S47008 Brand SUA4cars Surface Finish Polished, Rust Protected Other Part Number 80286210001 Payment 1.We only accept PayPal. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) Shipping 1. Orders processed within 24 hours of payment verification. 2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address. 3. The images shown are not the actual item and are for your reference only. 4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! Returns 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 day s, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must vide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. Custome Services Q: How do I pay for my purchase? A: MY store accepts PayPal. Q: When will the item be shipped out? A: This item will be shipped with 2 business day once payment completed. Q: Where is my tracking number? A: Please log on your account, click “my eBay”–>”my summary”, or open your email box and find the shipping notification email. Q: How do I return an item? A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. Feedback 1. We will leave a feedback once we get your payment. 2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers. 3. If you are satisfied with the product you received, wish you can leave us a feedback. DESCRIPTION PAYMENT SHIPPING RETURN POLICY CONTACT US Pair For Honda Element 03-2011 Honda CR-V Front or Rear Wheel Bearing LH or RH What’s in the box? 2 Pcs Wheel Bearing and Hub Assembly Specifications: Location: Front Wheel Material: Bearing Steel ABS Sensor Included: No Outside Diameter: 84 MM Design:Double Row Angular Contact Inner Race Bore: 45 MM Compatible Vehicles: Fits Acura Cl 2001-2003 Fits Acura Mdx 2001-2002 Fits Acura Rsx 2002-2006 Fits Acura Tl 1999-2003 Fits Honda Accord 1998-2002 Fits Honda Civic 2004-2005 Fits Honda Cr-V 1997-2001 Fits Honda Cr-V 2002-2004 Fits Honda Element 2003-2011 Fits Honda Pilot 2003-2007 Fits Honda Pilot 2008 Fits Honda Prelude 1997-2001 Fits Honda S2000 2000-2009 The wheel hub bearing needs to be replaced in the following situations（notes） A humming, rumbling or growling noise that increases with acceleration or as the vehicle turns Vibration, felt in the steering wheel, which changes with vehicle speed or as the vehicle turns Looseness or excessive play* in the steering wheel (especially while driving over rough road surfaces) A loud, constant grinding noise when driving the vehicle (heard in the most severe cases of a wheel bearing failure) Puling to one side when braking Roughness or vibration when rotating the wheel with the vehicle off the ground Excessive brake pedal “play” (can also indicate excessively loose wheel bearings) ABS light illumination or system issues (may be related to failure of the ABS sensor in the hub assembly or the internal sensor in the wheel bearing) Purpose and Commitment : We insist on innovation and development. Our everlasting purpose is high quality , Integrity-based and Full service. Removing and Installing a Hub Unit Bearing: 1. Wheel End Disassembly Remove all old lubricant from the rotor/ hub assembly and spindle. Clean the rotor/hub assembly and spindle with kerosene or mineral spirits. Inspect the spindle for wear. Use a fine file, wire brush, emery cloth or honing stone to remove any debris, nicks or burrs. Follow the vehicle manufacturer’s recommendation for permissible spindle wear. Apply a light grease coating on the cone seats to ease installation and prevent fretting. 2. Clean and Inspect Hubs and Spindles Use a cup driver or mild steel bar to drive the new inner cup and outer cup into the hub/rotor assembly until solidly seated against the hub shoulders. Be careful not to damage the cup surfaces. Never use a bearing cone assembly to drive a cup. 3. Install cups Use a cup driver or mild steel bar to drive the new inner cup and outer cup into the hub/rotor assembly until solidly seated against the hub shoulders. Be careful not to damage the cup surfaces. Never use a bearing cone assembly to drive a cup. 4. Lubricate Use a mechanical grease packer to pack the inner bearing cone assembly with grease. Place the bearing cone assembly, small end down, into the grease packer funnel. Plug the bore of the large end of the bearing cone assembly with the conical retainer. Firmly press down on the conical retainer. This forces the grease between the rollers, cage and cone. Smear excess grease on the outside of the bearing cone assembly. Pack grease between the inner and outer cups in the hub cavity. Also, liberally coat the hub cap inner wall. This layer combats moisture and retains the grease in the inner and outer bearing cone assemblies. 5. Install Grease Seal Replace the grease seal when it leaks or when bearings are being repacked or replaced. Install the inner bearing cone assembly in the hub, then install the new seal. Make sure the seal lips are pointed in the right direction following the vehicle manufacturer’s specification. Use the proper seal installation tool. 6. Install Rotor/Hub Assembly Be careful not to damage the seal against the spindle when sliding the rotor/hub assembly back over the spindle. After following Step 4, pack the outer bearing cone assembly with grease. Install the outer bearing cone assembly, washer and adjusting nut on the spindle. 7. Bearing Adjustment Use a torque wrench to tighten the adjusting nut to 50 ft. lbs. while turning the rotor. Back off the adjusting nut 1 full turn. Re-torque the nut to 10 ft. lbs. while turning the rotor. Next, back off the adjusting nut ¼ turn. Lock the nut with a new cotter pin. 8. Check Bearing Adjustment Use a dial indicator to measure endplay. Mount the indicator base as close to the center of the hub/rotor as possible. With the indicator tip against the end of the spindle, set the indicator at zero. Grasp the rotor at three o’clock and nine o’clock. Push the rotor in while oscillating and read the dial indicator. Dial IndicatorPull the rotor out while oscillating and read the dial indicator again. The bearing end-play is equal to the total indicator movement, which should be between 0.001” and 0.005.” If not, repeat steps 7 and 8. Reinstall all components as the vehicle manufacturer recommends. Warning failure to observe the following warnings could create a risk of death or serious injury!!! Item Specifics Placement on Vehicle : Left Warranty : 1 Year Manufacturer Part Number : SUA802862cars Interchange Part Number : 510050,42200S3VA01, 44300S47008 Brand : SUA4cars Surface Finish : Polished, Rust Protected Other Part Number : 80286210001 Payment 1.We only accept PayPal. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) Shipping 1. Orders processed within 24 hours of payment verification. 2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address. 3. The images shown are not the actual item and are for your reference only. 4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! Returns 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 day s, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must vide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. Custome Services Q: How do I pay for my purchase? A: MY store accepts PayPal. Q: When will the item be shipped out? A: This item will be shipped with 2 business day once payment completed. Q: Where is my tracking number? A: Please log on your account, click “my eBay”–>”my summary”, or open your email box and find the shipping notification email. Q: How do I return an item? A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. Feedback 1. We will leave a feedback once we get your payment. 2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers. 3. If you are satisfied with the product you received, wish you can leave us a feedback. All rights reserved.