Gibson 2 Ton 14.3 SEER Condenser, 92% 72,000 BTU Furnace & 17" Coil HVAC Package

Gibson 2 Ton 14.3 SEER Condenser, 92% 72,000 BTU Furnace & 17″ Coil Package Contact us with your zip code and we’ll be glad to get you a freight quote. Note: Condenser can only be shipped to the following states: CO, CT, ID, IL, IN, IA, KS, ME, MA, MI, MN, MO, MT, NE, NH, NJ, NY, ND, OH, OR, PA, RI, SD, UT, WA, WV, WI, WY. All other states must use 15 SEER minimum by law. **Local pickup is available** Gibson 2 Ton 14.3 SEER2 R410a Condenser WSA3BE4M1SN24K Quality Compressor : State-of-the-art Copeland Scroll™ compressor is standard equipment. Designed Using Galvanized Steel : With powder-coated paint and a gloss finish that eliminates sharp edges and reduces scratching. Permanently Lubricated Motor : A heavy duty PSC motor for long lasting reliability and quiet operation. Requires no maintenance and is completely protected from rain and snow. Removable Top Grille Assembly : Allows ease of service from the top without disconnecting fan motor leads. High Pressure Switch : Protects against abnormally high system pressures. Auto-reset feature prevents nuisance service visits. Liquid Line Filter Drier : Included with unit, field installed. One Piece Top/Orifice : Designed for maximum airflow and quiet operation. Easy Compressor and Control Access : Designed to make servicing easier for the contractor, access panels are provided to all controls and the compressor from the side of the unit. Composite Base Pan : Absorbs sound and is corrosion resistant. Composite is also stronger and lighter than steel. Swept Wing Fan Blade : Designed to significantly reduce unwanted noise. All-Aluminum Coils : All aluminum coils in all models which provides high corrosion resistance. Servicer-Friendly Jacket : Side panels can be easily removed and replaced without removing the top grill. Specs: Model # WSA3BE4M1SN24K Single Stage Refrigerant Type: R-410a Install Location: Outdoor Cooling Only Capacity: 2 Tons (24,000 BTU) SEER: 14.3 60 Hz Phase: 1 Voltage: 208/230 Recommended Breaker Size: 25 Amp Depth: 30-3/4″ Width: 30-3/4″ Height: 27-1/4″ Approximate Weight: 138 Sound Rating: 69 dBA Liquid Line Size: 3/8″ Suction Line Size: 3/4″ Parts Warranty: 10 Years Upon Registration Compressor Warranty: 10 Years Upon Registration AHRI Certified: Yes ETL Listed: Yes Gibson 2 Ton 17.5″ Wide Vertical Cased A-Coil with TXV Valve – C74BAMX24C-B Specs: Vertical use only Factory installed TXV Valve Refrigerant: R-410A Casing: Cased Style: A Coil Capacity: 2 tons (24,000 BTUs) Suction Line Size: 3/4″ Liquid Line Size: 3/8″ Width: 17-1/2″ Height: 26-3/4″ Height of Liquid Line: 23-1/2″ Height of Suction Line: 21-1/2″ Gibson KG7SC-072D-T24BP 92% 72,000 BTU 17″ Upflow/Horizontal Natural Gas Furnace • iSEER: Energy efficient, brushless DC (ECM) motor gives up to 1 SEER point efficiency gain in cooling. • 100% fired and tested: All units and each component are tested on the manufacturing line. • Best packaging in the industry: Unique corner post design assures product will arrive to the homeowner dent free. • 30 second blower delay at start-up: assures a warm duct temperature at furnace start-up. Adjustable blower off settings (60, 90, 120 and 180 seconds). • 30 second post purge: increases life of heat exchanger. • Hot surface igniter: Innovative application of a silicon nitride type igniter.Utilizes proven Smartlite® technology. • Color coded wire harness: Designed to fit the components, all with quick-connect fittings for ease of service and replacement. • Flexible category IV venting system: May be vertically or horizontally vented using either a one-pipe or two-pipe system for maximum flexibility in installation. • High Static Blowers: All models equipped with high static ECM blowers. • 16 speeds for heating and cooling: enables flexible airflow. • Low Boy Height: Easy to apply in low ceiling applications, works well with taller high SEER coils, easier to handle and install. • Tubular primary heat exchanger: Heavy gauge aluminized steel heat exchanger and stainless steel secondary heat exchanger: assures a long life. • 90 second fixed cooling cycle blower-off delay (TDR): increases cooling performance when matched with a Nortek Global HVAC coil. • LP convertible: Simple burner orifice and regulators pring change for ease of convertibility. • Diagnostic lights for easy troubleshooting without counting flashes: Dedicated light for flame signal strength and2 lights in combination to indicateallother fault codes with easy to recognize states without counting flashes. • Incorporates integrated control board: with connections for electronic air cleaner and humidifer. • Two piece door design: enhances furnace appearance and uses captured screws to prevent losing door screws. • Blower Compartment: Sealed door to reduce air leakage and insulated for ultra quiet operation. • Sealed Vestibule: reduces burner and inducer sound levels. • Furnace Air Leakage: These furnaces comply with Energy Star cabinet air leakage requirement of less than or equal to 2%.Keep the conditioned air flowing to where it’s needed Specs: 92.1% AFUE High Efficiency Single Stage Upflow/Downflow ECM Blower Motor Direct Vent or Non-Direct 17.5″ Wide 34-1/2″ High 28″ Deep BTU Input: 72,000 BTU Output: 66,300 Payment Method We accept PayPal. All payment arrangements should be made within 24 hours of purchase to assure prompt shipping. We can not hold or reserve this item. We do charge sales tax in Minnesota. This is calculated at checkout. PLEASE NOTE: All HVAC equipment should be installed by a licensed professional. Warranty is void if not installed by a licensed professional. Shipping Terms This item ships to anywhere in the continental USA. We cannot ship this outside of the 48 continental states. No shipments to Alaska/Hawaii. No international shipments. Please provide us with a valid contact phone number and physical address to assure a problem-free delivery. Please allow a minimum 3 – 4 business days for delivery. Returns and Miscellaneous Please ask any questions before buying. We will accept returns providing you contact us within 14 days after receiving your item. Feel free to contact us with any questions before purchasing. Return costs are your responsibility. It is your responsibility at the time of delivery to inspect the merchandise, especially for large appliances. If the packaging looks damaged do not sign for the delivery until the item is inspected. If it does not pass your inspection, tell the delivery company that you can not accept it. If the box has any damage, or if there is any reason for you to be at all concerned about damage, please write “PRODUCT DAMAGED” clearly on the sheet that they ask you to sign. Once you sign for the package you accept full responsibility. You have up to 48 hours to contact us either by phone or email to let us know if something is damaged. Even if you do not intend to install your merchandise right away, please be sure to check and make sure it arrived intact otherwise the claim will be up to you and we will not be responsible for the damage. If you wait more than two days, its hard to know if it was the shipper that caused the damage and we will not be able to file a claim with the shipping company. We will do everything in our power to fix the problem incurred by damage, but please be aware that it is your full responsibility to inspect all goods before signing for them.