ESP8285 Wifi Wireless Module Transmission IR Remote Control Development Board

ESP8285 Development Board The development board board Lexin ESP8285 ultra-low power UART-WiFi module and USB to TTL serial CH340 chip, can be easily developed for secondary development, access to cloud services, to achieve mobile phone 3/4G global control anytime, anywhere, accelerate Product prototype design. Based on the ESP8266, the ESP8285 integrates 1MB of Flash inside the chip to make it resistant to high temperatures up to 125 degrees Celsius! And the original ESP8266 source program can be used as it is. The module core processor ESP8285 integrates the industry-leading Tensilica L106 ultra-low-power 32-bit micro MCU in a small package with 16-bit compact mode, 80MHz and 160MHz clock speed, RTOS support, and integrated Wi-Fi MAC/ BB/RF/PA/LNA supports the standard IEEE802.11 b/g/n protocol, complete TCP/IP protocol stack. Users can use this module to add to existing devices Networking capabilities can also build standalone network controllers. The ESP8285 is a high-performance wireless SOC that offers maximum utility at the lowest cost, providing unlimited possibilities for WiFi functionality to be embedded in other systems. The ESP8285 is a complete, self-contained WIFI network solution that runs independently. The ESP8285 can be booted directly from an external flash memory when it is powered by the application and is the only application processor in the device. The built-in cache helps improve system performance and reduce memory requirements. It can also be used as a slave to be installed on other host MCUs. It can assume the task of WIFI adapter, and only needs to be connected through SPI/SDIO interface or IIC/UART interface. SOC Characteristics: Built-in 1 10 bit high precision ADC Peripheral Interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO Deep sleep keeps current at 10uA and shutdown current is less than 5uA Wake up, connect and pass packets within 2 ms Standby power consumption is less than 1.0mW (DTIM3) Built-in 1Mbyte SPI Flash Wi-Fi Features: Support for 802.11 b/g/n/e/i Support Station, SoftAP, SoftAP+STA mode Support for Wi-Fi Direct (P2P) Supports hardware acceleration of CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC P2P discovery, P2P GO mode/GC mode and P2P power management WPA/PA2 PSK and WPS 802.11 i security features: pre-authentication and TSN Support for 802.11n (2.4 GHz) 802.1h/RFC1042 frame packing Seamless roaming support Support AT remote upgrade and cloud OTA upgrade Support for Smart Config (including Android and iOS devices) Connect MicroUSB to the computer, install CH340-USB to TTL serial port driver, serial assistant debug AT command or use SDK integrated development environment ESP-01F Product Specifications: Package: SMD-18 SPI Flash: Built-in 8Mbit Support interface: UART/GPIO/ADC/PWM IO port: 9 Serial port rate: support 300-4608000bps, default 115200bps Spectrum range: 2412-2484MHz Power supply range: 3.0V- 3.6V Supply current: >300mA Working temperature: -20 ° C ~ 85 ° C Storage environment: -40 ° C ~ 90 ° C, <90% RH CCK, 1Mbps: -90dBm CCK, 11Mbps: -85dBm 6Mbps (2 BPSK): -88dBm 54Mbps (3/4 64-QAM): -70dBm HT20, MCS7 (65Mbps, 72.2Mbps): -67dBm Product Features: Smallest 802.11b/g/n Wi-Fi SOC module Low-power 32-bit CPU for dual application processor Main frequency up to 160MHz Built-in 10bit high precision ADC Supports interfaces such as UART/GPIO/ADC/PWM SMD-18 package for easy soldering and testing Support multiple sleep modes, deep sleep current resists 20uA Embedded Lwip protocol stack Support STA/AP/STA+AP working mode General AT command can get started quickly Support for serial local upgrade and remote firmware upgrade (FOTA) ESP-01M Features: Frequency up to 160MHz Built-in 10 bit high precision ADC Support UART / GPIO / IIC / PWM / ADC and other interfaces Integrated Wi-Fi MAC / BB / RF / PA / LNA Supports multiple hibernation modes with standby power as low as 1.0 mW Embedded Lwip protocol stack Support STA / AP / STA + AP working mode Support Smart Config / AirKiss a key distribution network Serial port speed up to 4Mbps Universal AT command can get started quickly, you can brush Web configuration firmware Support serial local upgrade and remote firmware upgrade (FOTA) ESP-M2 SOC Characteristics Built-in Tensilica L106 ultra-low power 32-bit microprocessor, clocked at 80MHz and 160MHz support RTOS Built-in TCP / IP protocol stack Built-in 1-channel 10-bit high-precision ADC Peripheral Interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO The deep sleep hold current is 10uA and the shutdown current is less than 5uA Wake up within 2 ms, connect and pass the packet Standby power consumption less than 1.0mW (DTIM3) Built-in 1M bytes of SPI Flash Wi-Fi Features: Supports 802.11 b / g / n / e / i Support Station, SoftAP, SoftAP + STA mode Support for Wi-Fi Direct (P2P) Supports CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC hardware acceleration P2P discovery, P2P GO mode / GC mode and P2P power management WPA / PA2 PSK and WPS 802.11 i security features: pre-authentication and TSN Hold 802.11n (2.4 GHz) 802.1h / RFC1042 frame encapsulation Seamless roaming support Support AT remote upgrade and cloud OTA upgrade Support for Smart Config features (including Android and iOS devices) ESP-M3 Application Scenario: Household appliances Home automation Smart socket, smart light Mesh network Baby monitor IP camera sensor network can wear electronic products Security ID tag Wireless location awareness Wireless positioning system beacon Industrial wireless control ESP-01E The Wi-Fi module, also known as the serial port Wi-Fi module, belongs to the transmission layer of the Internet of Things. Its function is to convert the serial port or TTL level into an embedded module that conforms to the Wi-Fi wireless network communication standard. The built-in wireless network protocol IEEE802.11b.gn Protocol stack and TCP/IP protocol stack. Traditional hardware devices embedded in Wi-Fi modules can directly use Wi-Fi to connect to the Internet, which is an important part of realizing wireless smart home, M2M and other Internet of Things applications. Characteristic: Complete 802.11b/g/n Wi-Fi SoC module Built-in Tensilica L106 is a low-power 32-bit micro MCU, the main frequency is 80Mhz and 160Mhz, and it supports RTOS Built-in 1 channel 10bit high precision ADC Built-in Flash Support UART/GPI0/ADC/PWM/SP1/I2C interface Adopt DIP-18 package Integrated Wi-Fi MAC/ BB/RF/PA/LNA Support multiple sleep modes, deep sleep current as low as 20uA Serial rate up to 4Mbps Embedded Lwip protocol stack Support STA/AP/STA+AP working mode Support Android, I0S Smart Config (APP) /AirKiss (WeChat) one-click network configuration Support serial port local upgrade and remote firmware upgrade (FOTA) General AT commands can be used quickly Support secondary development, integrated Windors, Linux development environment Parameters: Module Union Number ：ESP-01E Package ： DIP-18 Size ：18*17*2.8(±0.2)M Antenna form ： IPEX antenna or spring antenna Spectrum range ：2400~ 2483. 5MBHz Working temperature ：-40°C~85° C Storage environment ：-40 °C~125°C. <90%RH Power supply range ：Power supply voltage 3.0V~3.6V, power supply current>500mA: typical value 3.3V Support interface ：UART/GPIO/ADC/PWM/SPI/I2C Number of I0 ports ：11 Serial port rate supports ： 110~4608000 bps, the default is 115200 bps Security ：WEP/WPA-PSK/WPA2-PSK SPI Flash ：chip integrates 1MB/2MB Flash ESP8285 IR Infrared Module It is a Infrared ESP8285 Wireless WIFI Transceiver Module.The esp-01m module with ESP8285 as the core be used as the master control, The program is the same as ESP8266. The module board is equipped with an infrared receiving tube and an infrared transmitting tube which are respectively io14 and io4 controlled, and a burning port is set apart. The demonstration program can read and emit infrared key values and raw codes,user can record infrared remote controls in your home , which can be controlled remotely if connected to the Internet of things platform. Feature: 1.Support Infrared control 2.Support wireless WIFI control 3.Support firmware update Parameter: Model: ESP_IR-TR Work Voltage:DC 5V Work Temperature:-25~85 Work Humidity:5%~95%RH Update Firmware: 1.Connect IO0 and GND pins. 2.Connect module to PC by USB to UART converter. 3.Open software ‘FLASH DOWNLOAD TOOLS V3.6.4’. 4.Set parameters. 5.Click START to download firmware. 6.Remove connect between IO0 and GND pins then update complete. When supplying power, you need to look for 5V and GND. The circuit has no reverse connection protection, and the wrong connection may burn the chip. ESP-01D The module core processor ESP8285 integrates the industry-leading Tensilica L106 ultra-low power 32-bit micro MCU in a smaller size package, with 16-bit reduced mode, the main frequency supports 80MHz and 160MHz. Support RTOS. Integrated Wi-Fi MAC/BB /RF/PA/LNA, onboard antenna. Support standard EEE802.11b/g/n protocol, complete TCP/IP protocol stack. Users can use this module to add networking capabilities to existing devices, or they can build an independent network controller. ESP8285 is a high-performance wireless SoC that provides maximum practicality at the lowest cost and provides unlimited possibilities for Wi-Fi functions to be embedded in other systems. Features: Complete 802.11b/g/n WIFI SoC module Built-in Tensilica L106 ultra-low power 32-bit micro MCU. Main frequency support, 80MHz and 160MHz. Support RTOS Support GPIO/PWM interface Built-in Flash Integrated Wi-Fi MAC/BB/RF/PA/LNA Support multiple sleep modes Embedded Lwip protocol line Support STA/AP/STA+AP working mode Support Smart Config(APP)/ Arkiss(WeChat) one-click distribution network for Android and IOS Supports remote firmware upgrade (FOTA) General AT command can get started quickly Support secondary development, integrated Windows, Linux development environment Product Parameters: Module model: ESP-01D Package: DIP-6 Size: 13.5*8.5*2.6(±0.2)MM Antenna form: external Spectrum range: 2400~2483.5MHz Working temperature: -20°C ~70°C Storage environment: -40°C~125°C, <90%RH Power supply range: power supply voltage 3.0V~3.6V. power supply current>500mA Support interface: GPIO/PWM Number of IO ports: 3 Serial port rate: support 110~4608000ps, default 115200bps Security: WEP/WPA-PSK/WPA2-PSK SPI Flash: 16Mbit (chip built-in) Pin Definition: 1.ANT: RF antenna interface, requires external antenna 2.IO12: GPIO12 3.IO4: GPIO4 4.VDD: 3.3V power supply; the output current of the power supply is recommended to be above 500mA 5.IO14: GPIO14 6.GND: ground Product Size: