Crossover PCB for the Nexus Tower or Nexus Center Channel DIY speaker design

Custom printed circuit board designed for the crossover of the Nexus MTMWW Tower or WTMW Center Channel DIY speaker design. Makes crossover assembly quick and easy! The board measures 7.25″ x 5.25″ and feature large solder pads and copper traces for great electrical connectivity Note photos of fully assembled crossovers are for reference only. Includes: 1x Crossover PCB for the Nexus Tower/Center speaker design. 4x Terminal blocks which accept up to 12 gauge bare wire. 4x Snap in PCB standoffs. 4x Mounting screws (screw finish may vary). Requires: Crossover components for the Nexus Tower or Nexus Center speaker design. Compatible components tested for fit on this PCB listed below, other components of identical value may fit but verify dimensions are similar to the components listed. Components required for Nexus MTMWW Tower Design: LF L1 – 4mH – Dayton Audio 4.0mH 18 AWG I Core -or- Erse Audio 4.0mH 18 AWG I-Core LF L2 – 0.1mH – Dayton Audio 0.10mH 20 AWG Air Core -or- Jantzen Audio 0.10mH 20 AWG air core LF C1 – 100uF – Parts Express 100uF Non-Polarized Electrolytic Capacitor LF C2 – N/A – Not used for this design LF R1 – 0.5 Ohm – Dayton Audio DNR-0.51 MF C1 – 39/40uF – Parts Express 22uF + 17uF Non Polarized Electrolytic Capacitors -or- Dayton Audio DMPC-40 MF C2 – 0.68uF – Dayton Audio DMPC-0.68 MF C3 – 12uF – Parts Express 12uF Non-Polarized Electrolytic -or- Dayton Audio DMPC-12 MF L1 – 1mH – Dayton Audio 1.0mH 20 AWG Air Core -or- Jantzen Audio 1.0mH 20 AWG Air Core MF L2 – 0.4mH – Dayton Audio 0.40mH 20 AWG Air Core -or- Jantzen Audio 0.40mH 20 AWG Air Core MF R1 – 5 Ohm x2 – Dayton Audio DNR-5.1 -or- 5 Ohm 10w wire wound resistor MF R2 – 1 Ohm – Dayton Audio DNR-1.0 -or- 1 Ohm 10w wire wound resistor HF C1 – 4.3uF – Dayton Audio DMPC- 4.3 HF L1 – 0.4mH – Dayton Audio 0.40mH 20 AWG Air Core -or- Jantzen Audio 0.40mH 20 AWG air core HF R1 – 2.2 Ohm – Dayton Audio DNR-2.2 -or- 2.2 Ohm 10W wire wound resistor Components required for Nexus WTMW Center Channel Design: LF L1 – 5mH – Dayton Audio 5.0mH 18 AWG I Core -or- Erse Audio 5.0mH 18 AWG I-Core LF L2 – 0.05mH – Dayton Audio 0.05mH 18 AWG Air Core -or- Jantzen Audio 0.05mH 18 AWG air core LF C1 – 50uF – Parts Express 50uF Non-Polarized Electrolytic Capacitor LF C2 – 12uF – Parts Express 12uF Non-Polarized Electrolytic Capacitor LF R1 – 0.5 Ohm – Dayton Audio DNR-0.51 -or- 0.5 Ohm 10W wire wound resistor MF C1 – 15uF – Parts Express 15uF Non Polarized Electrolytic Capacitor -or- Dayton Audio DMPC-15 MF C2 – 0.68uF – Dayton Audio DMPC-0.68 MF C3 – 8.2uF – Dayton Audio DMPC-8.2 MF L1 – 1.5mH – Dayton Audio 1.5mH 20 AWG Air Core -or- Jantzen Audio 1.5mH 20 AWG Air Core MF L2 – 0.7mH – Dayton Audio 0.70mH 20 AWG Air Core -or- Jantzen Audio 0.70mH 20 AWG Air Core MF R1 – N/A – Bypass component position with short wire MF R2 – 2 Ohm – Dayton Audio DNR-2.0 -or- 2 Ohm 10w wire wound resistor HF C1 – 4.3uF – Dayton Audio DMPC- 4.3 HF L1 – 0.45mH – Dayton Audio 0.45mH 20 AWG Air Core -or- Jantzen Audio 0.45mH 20 AWG air core HF R1 – 4 Ohm – Dayton Audio DNR-4.0 -or- 4 Ohm 10W wire wound resistor Assembly: Glue components to the correct positions on the board (hot melt glue works great). Secure inductors with non metallic cable ties. Solder components leads to the pads on the bottom of the board. Attach wires from input and drivers to the crossover. Insert standoffs into the bottom of the board at the four corners and mount the crossover to the enclosure.