3.5K Trailer Axle 5 lug Trailer, Cargo, Dump, Utility Axle 3500 lbs Boat Axle

3,500 lbs Rockwell American Idler trailer axle 5 lug !!! MADE IN USA !!!! FULLY ASSEMBLED READY TO INSTALL ON TRAILER Kit Includes: (1) 3,500 lbs. trailer axle fully assembled with 5 lug idler hubs. EZ lube Grease This axle is ready to go. Simply drop your old axle and throw this new axle on your trailer. This is a brand new brake axle rated at 3500 lbs. AXLE SPECIFICATIONS: Country Assembled: The U.S.A. Brand: Rockwell American Capacity Per Axle (LBS): 3,500 Stud Size: 1/2″ Hubs/drums: 5 Lug Drums Spindles: #84 Spindle Size: 1-1/16″ Axle Tubing Diameter (Inch): 2 3/8″ Axle Tubing Thickness: .180″ Lubrication: EZ-Grease Zerks in Spindles Spring Pads: Welded on Axle Brake: no brakes Hubs: 5 lug idler hubs installed on axles. Brake Flange: 4 Bolt Welded on Axle Pre-Greased: Yes Inner Bearing: L68149 Outer Bearing: L44649 Suspension: Leaf Spring Cambered: Yes Under-slung: Yes (the axle sits on top of the springs) FULLY ASSEMBLED, READY TO INSTALL ON TRAILER. Replaces Dexter, AL-KO, Hayes, Lippert Axles, Rockwell American, and Just about any other brand axle. Very Important to get correct axle you need please double check and triple check your bolt pattern and your spring center measurement. See below on how to properly measure axle. How to Determine what axle you need: If your building a trailer from scratch then you do not have to worry about measuring anything. Just pick the width of axle you would like Hub Face (HF) : Refers to the length of the axle measured from the base of one wheel stud to the base of the wheel stud on the opposite side of the axle. (where the studs protrude out from the hub or where the two wheels butt up to each other) (when hubs are mounted on the beam). You can measure from one hub where the studs start on the drum, to the hub on the other side of the axle. You can also get this by measuring from where the two wheels butt together on one side of the axle to where the two wheels but up together on the other side of the axle. (This measurement is important but not a deal breaker if its a inch or so different than what we show) Spring Center (SC): is the approximate width of your trailer. It is measured from the center of the spring seat on one side of the axle to the center of the seat on the other. This axle beam comes with the spring seats welded on. The easiest way to measure this is to have a friend help you. Have your friend hold the tape measure in the center of one spring one the axle while you pull the tape measure down the same axle to the other side of the axle to the center of the other spring on the same axle. This will give you your (SC) or Spring Center Measurement. If your like myself and do not have many friends to help you out. The easiest way to measure when by yourself is: Hook the tape measure on the outside of one spring, pull down the axle to the inside of the other spring on the axle axle. This will also give you your (sc) or Spring Center measurement. ( This measurement is the most important measurement to get, so please double and triple check your measurement ) BOLT PATTERN Use the distance between the center of one bolt hole to the center of the bolt hole adjacent to it: If the distance is: 2-5/8″ – the bolt pattern is 5 on 4-1/2 2-3/4″ – the bolt pattern is 5 on 4-3/4 3″ – the bolt pattern is 5 on 5 3-1/4″ – the bolt pattern is 5 on 5-½ (SEE DIAGRAM IN PICTURE LISTING) Free Shipping In some cases we may ask that you have a commercial address to ship to or that you pick up at the freight terminal (if you purchase multiple items) Freight Residential Delivery is available at an additional cost. OR Pick up at our distribution center Trailer Parts Unlimited 631 TX-75 North Huntsville TX 77320 MM IN GOD WE TRUST